Por favor, use este identificador para citar o enlazar este ítem: http://dspace.espoch.edu.ec/handle/123456789/15665
Título : Plan de seguridad industrial en el área del taller de mantenimiento de maquinaria pesada del Terminal Portuario ECUAESTIBAS S.A de la ciudad de Guayaquil
Autor : Farfán Scotland, Luis Geovanny
Director(es): Moyano Alulema, Julio César
Tribunal (Tesis): Santillán Mariño, Carlos José
Palabras claves : TECNOLOGÍA Y CIENCIAS DE LA INGENIERÍA;PLAN DE SEGURIDAD;SEGURIDAD INDUSTRIAL;GESTIÓN DE RIESGOS LABORALES;MATRIZ DE RIESGOS
Fecha de publicación : 15-nov-2019
Editorial : Escuela Superior Politécnica de Chimborazo
Citación : Farfán Scotland, Luis Geovanny. (2019). Plan de seguridad industrial en el área del taller de mantenimiento de maquinaria pesada del Terminal Portuario ECUAESTIBAS S.A de la ciudad de Guayaquil. Escuela Superior Politécnica de Chimborazo. Riobamba.
Identificador : UDCTFM;85T00582
Abstract : The realization of the Industrial Safety plan is a technical study on the risks present in the maintenance workshop of ECUAESTIBAS S. A. to improve the Occupational Safety and Health Management corresponding to the area of the maintenance workshop of tractor-trailers, a measurement of the existing risks in the company is made through the use of the risk matrix established by the National Institute of Safety and Health at Work which was within physical, chemical, mechanical, ergonomic and psychosocial risks, which were identified and a valuation is given according to the recommended by the INSHT qualifying them as trivial, tolerable, moderate, important and intolerable, once it has been identified the risks present in the maintenance workshop of the company, tolerable, moderate, important and intolerable. Once the risks have been identified, we proceed to manage them to eliminate or reduce them, always trying to eliminate the risk, that is to say, always trying from the cause or origin of the risk, and from then on, if elimination is not possible, then we manage them through mechanisms such as training, information, or individual protection. The order in which the management was given was from prevention, which is at the origin, then to the organization, then to collective protection, individual protection, personnel training, and information about the risks, their consequences, and the way to prevent or minimize them. The study shows that mechanical risks account for 39% of all existing risks, followed by physical risks, which account for 9.9% of the risks. The analysis shows that if any of the risks shown, such as disorder, are eliminated, this immediately leads to the elimination of risks. It is concluded that by applying the safety plan in the company the risks found are reduced to tolerable and trivial, disappearing the moderate and important ones.
Resumen : La realización del plan de Seguridad Industrial es un estudio técnico sobre los riesgos presentes en el taller de mantenimiento de ECUAESTIBAS S. A. para mejorar la Gestión de Seguridad y Salud en el Trabajo correspondiente al área del taller de mantenimiento de tractocamiones , se realiza una medición de los riesgos existentes en la empresa a través del uso de la matriz de riesgos establecida por el Instituto Nacional de Seguridad y salud en el Trabajo los cuales estuvieron dentro de riesgos físicos, químicos, mecánicos, ergonómicos y psicosociales, a los cuales se los identifico y se da una valoración en función de lo recomendado por el INSHT calificándolos como triviales, tolerables, moderados, importantes e intolerables, una vez que se tiene identificado los riesgos se procede a realizar la gestión para eliminarlos o reducirlos siempre tratando de eliminar el riesgo, es decir tratando siempre desde la causa u origen del riesgo, y de ahí en adelante si la eliminación no es posible, entonces se dio gestión a través de los mecanismos como capacitación, información o protección individual. El orden en el que se dio la gestión fue desde la prevención que es en el origen, luego hacia la organización, posteriormente a la protección colectiva, protección individual, formación al personal e información acerca de los riesgos sus consecuencias y la forma de prevenirlos o de minimizarlos. Una vez hecho el estudio se detecta que los riesgos mecánicos abarcan el 39% del total de los riesgos existentes seguidos de los riesgos físicos que tienen el 9,9% de los riesgos. El análisis demuestra que si se elimina alguno de los riesgos mostrados como el desorden este inmediatamente hace que se eliminen riesgos. Se concluye que al aplicar el plan de seguridad en la empresa los riesgos encontrados se reducen a tolerables y triviales, desapareciendo los moderados y los importantes.
URI : http://dspace.espoch.edu.ec/handle/123456789/15665
Aparece en las colecciones: Ingeniero Industrial

Ficheros en este ítem:
Fichero Descripción Tamaño Formato  
85T00582.pdf5,48 MBAdobe PDFVista previa
Visualizar/Abrir


Este ítem está sujeto a una licencia Creative Commons Licencia Creative Commons Creative Commons