Por favor, use este identificador para citar o enlazar este ítem: http://dspace.espoch.edu.ec/handle/123456789/7640
Título : Diseño, fabricación y pruebas de un prototipo de arnés de sujeción y operación, para la desmalezadora utilizada en el sector agrícola en la Empresa “APROCAI” ubicada en la Provincia de Chimborazo Cantón Cumandá mediante la aplicación del software ErgoMet 3.0
Autor : Matute Rodríguez, Oscar Mauricio
Tandazo Baque, Adolfo Humberto
Director(es): Carrera Oña, Gustavo Efrain
Tribunal (Tesis): Cayán Martínez, Juan Carlos
Palabras claves : ERGONOMÍA;ANSYS (SOFTWARE);ERGO IBV (SOFTWARE);ARNÉS DE SUJECIÓN;MANGO DE OPERACIÓN;TRABAJO EN MATERIALES
Fecha de publicación : 1-ago-2017
Editorial : Escuela Superior Politécnica de Chimborazo
Citación : Matute Rodríguez, Oscar Mauricio; Tandazo Baque, Adolfo Humberto. (2017). Diseño, fabricación y pruebas de un prototipo de arnés de sujeción y operación, para la desmalezadora utilizada en el sector agrícola en la Empresa “APROCAI” ubicada en la Provincia de Chimborazo Cantón Cumandá mediante la aplicación del software ErgoMet 3.0. Escuela Superior Politécnica de Chimborazo. Riobamba.
Identificador : UDCTFM;85T00465
Abstract : The current research work addresses desing, manufacturing and testing of a prototype of a holding and operation harness at “APROCAI” company located in Chimborazo province, Cumandá canton, by applying Ergomet 3.0 software aiming to develop the ergonomic study of the influence of loads, determine the consecuences of repetitive movements and evaluate the new desing of the subjection and operation system by means of the application of the software: Solid Works, Ansys, Ergo IBV; the machining of the pieces will be performed by using other software tolos such as: Matter Controls and Netfabb Basic. By using the inductive method to gather essential elements of the observation; and analytical methods in order to reach the depth of the research; thechniques as surveys, direct observation and Check-list were used, by using Ergo IBV software the following results were gathered; the average frequency, the Reba -1 punctuacion and the risk level is “invaluable”; by using the Ansys software, data were registered with a strength of 7.9 Kgf (77.42N) with PLA polymer, having as a result a total deformaion of 4.7 mm in the holding zone of the appilied load, noticing that the total deformation of the harness desing is not affected. With the statistical analysis it was determined that the subjection and operation harness prototype for the mowing truck in the farming area, affects importantly in the reduction of tiredness levels. It is concluded that the evaluation of the technical and ergonomic study of the subjection harness determined the adequacy of the material, not only for reaching the technical parameters of desing but also its low manufacturing cost. It is recommended to have active pauses in the suggested times so that it reduces the exhaust levels of the workers.
Resumen : En el presente trabajo de investigación se realiza el diseño, fabricación y pruebas de un prototipo de arnés de sujeción y operación, en la empresa “Aprocai” ubicada en la provincia de Chimborazo cantón Cumandá mediante la aplicación del software Ergomet 3.0, con la finalidad de realizar el estudio ergonómico de la influencia de las cargas y determinar las consecuencias de los movimientos repetitivos y evaluar el nuevo diseño del sistema de sujeción y operación mediante los Software: Solid Works, Ansys, Ergo IBV y ejecutar el mecanizado asistido por computador mediante los software: Matter Control y Netfabb Basic. Utilizando el método inductivo examinando elementos primordiales de observación, analíticos por que se reconoce la profundidad de la investigación, se utilizaron también técnicas como la encuesta, observación directa y Check-list; a través del software Ergo IBV se encontraron los siguientes resultados; la frecuencia media, la puntuación Reba -1 y el nivel de riesgo es “inapreciable”; con el software Ansys se ingresaron datos con una fuerza de 7.9 Kgf (77.42 N) con material de polímero PLA, dando como resultado una deformación total de 4.7 mm en la parte de soporte de la carga efectuada, evidenciando que no se afecta a la deformación total del diseño del arnés. Con el análisis estadístico se determina que el prototipo de arnés de sujeción y operación para la desmalezadora utilizada en el sector agrícola incide significativamente en la reducción de los niveles de fatiga. Se concluye que la evaluación del estudio técnico y ergonómico del arnés de sujeción determino que el material seleccionado es el adecuado, no solo porque cumple parámetros técnicos de diseño, sino también por su bajo costo de fabricación. Recomendándose realizar pausas activas en los tiempos propuestos, para de esta forma tener reducción de niveles de fatiga en los operarios.
URI : http://dspace.espoch.edu.ec/handle/123456789/7640
Aparece en las colecciones: Ingeniero Industrial

Ficheros en este ítem:
Fichero Descripción Tamaño Formato  
85T00465.pdf4,14 MBAdobe PDFVista previa
Visualizar/Abrir


Este ítem está sujeto a una licencia Creative Commons Licencia Creative Commons Creative Commons